3. 軸向振動/Axes,10 cycles per axis. 在測試過程中不能出現長久性的損壞. No permanent damage may occur during testing. 在電源開啟和關閉后,樣機能夠恢復到相當初條件. The SAMPLE has to restore to its original situation after power off/on.. 5.5 跌落試驗/Dropping Packed: 插墻式跌落高度為1米、桌面式跌落高度為760mm； 1M for wallmount type and 760mm for desktop type as above described; 測試臺面是厚13mm的夾木板，離地面高19-20mm The horizontal surface consists of hardwood at least 13mm thick, mounted on two layers of plywood each 19mm to 20mm thick,all supported on a concrete or equivalent non-resilient floor. 6、安全及EMI要求/SAFETYAND EMI REQUIREMENT: 6.1 安全:符合標準 Safety:accord with 6.2 高壓/DIELECTRIC STRENGTH Hi-Pot: 初級對次級/Primary to secondary: 3000Vac/10mA/60S or 4242Vdc/5mA/60S for type test. 6.3 絕緣抗阻/Iusulation resistance: 初級對次級/Primary to secondary:20MΩ min at 500V DC. 6.4 EMI標準/EMI STANDARD Meets the Limits of/測試符合 <1>.Fcc part15 class B rules <2>.EN55022 class B r廣東7.5V1.5A韓規KCC認證電源適配器

1、描述/ DESCRIPTION: 本規格書適應于CKA-Q30W The purpose of the document is to specify the functional requirements of a 30 Wswitching power supply. 2、輸入特性/INPUT CHARACTERISTICS: 2.1輸入電壓/Input Voltage: 額定電壓/Rated Voltage:100~240Vac 調整范圍/Variation Range:90-264Vac 2.2輸入頻率/Input Frequency: 額定頻率/ Rated Frequency: 50/60Hz. 調整頻率/Variation Frequency:47-63Hz 2.3輸入電流/Input Current: 當輸入交流電壓為額定值的下限電壓負載滿載時,比較大輸入交流電流0.8A. 0.8Amps maxAt any input voltage and rated, DC output rated load. 2.4浪涌電流/Inrush Current: 當輸出為額定負載,環境溫度為25℃,輸入240Vac冷態起機時無損壞. When the output of the rated load, the ambient temperature is 25℃, input from 240Vac cold machine without damage to 2.5 AC漏電流/Ac Leakage Current: 當輸入電壓240Vac時,比較大漏電流為0.25mA. 0.25mAMax.At240Vacinput.常州24V1A韓規KCC認證電源適配器

3. 軸向振動/Axes,10 cycles per axis. 在測試過程中不能出現長久性的損壞. No permanent damage may occur during testing. 在電源開啟和關閉后,樣機能夠恢復到相當初條件. The SAMPLE has to restore to its original situation after power off/on.. 5.5 跌落試驗/Dropping Packed: 插墻式跌落高度為1米、桌面式跌落高度為760mm； 1M for wallmount type and 760mm for desktop type as above described; 測試臺面是厚13mm的夾木板，離地面高19-20mm The horizontal surface consists of hardwood at least 13mm thick, mounted on two layers of plywood each 19mm to 20mm thick,all supported on a concrete or equivalent non-resilient floor. 6、安全及EMI要求/SAFETYAND EMI REQUIREMENT: 6.1 安全:符合標準 Safety:accord with 6.2 高壓/DIELECTRIC STRENGTH Hi-Pot: 初級對次級/Primary to secondary: 3000Vac/10mA/60S or 4242Vdc/5mA/60S for type test. 6.3 絕緣抗阻/Iusulation resistance: 初級對次級/Primary to secondary:20MΩ min at 500V DC. 6.4 EMI標準/EMI STANDARD Meets the Limits of/測試符合 <1>.Fcc part15 class B rules <2>.EN55022 class B r

3. 軸向振動/Axes,10 cycles per axis. 在測試過程中不能出現長久性的損壞. No permanent damage may occur during testing. 在電源開啟和關閉后,樣機能夠恢復到相當初條件. The SAMPLE has to restore to its original situation after power off/on.. 5.5 跌落試驗/Dropping Packed: 插墻式跌落高度為1米、桌面式跌落高度為760mm； 1M for wallmount type and 760mm for desktop type as above described; 測試臺面是厚13mm的夾木板，離地面高19-20mm The horizontal surface consists of hardwood at least 13mm thick, mounted on two layers of plywood each 19mm to 20mm thick,all supported on a concrete or equivalent non-resilient floor. 6、安全及EMI要求/SAFETYAND EMI REQUIREMENT: 6.1 安全:符合標準 Safety:accord with 6.2 高壓/DIELECTRIC STRENGTH Hi-Pot: 初級對次級/Primary to secondary: 3000Vac/10mA/60S or 4242Vdc/5mA/60S for type test. 6.3 絕緣抗阻/Iusulation resistance: 初級對次級/Primary to secondary:20MΩ min at 500V DC. 6.4 EMI標準/EMI STANDARD Meets the Limits of/測試符合 <1>.Fcc part15 class B rules <2>.EN55022 class B r

3、輸出特性/OUTPUT CHARACTERISTICS: 3.1 輸出功率/Power output 電壓 Voltage 相當小負載 Min. Load 額定負載 Rated. Load 峰值功率 Peak 輸出功率 Output power 5.5-24 0.01A-4A 0W 2 負載特性,調整率/Combined Load/Line Regulation 電壓 Voltage 相當小負載 Min. Load 額定負載 Rated. Load 線性調整 Line Regulation 負載調整率 Load Regulation 5.5-24Vdc 0.01A-4A ±2% ±5% 3.3 紋波和噪音Ripple and Noise: 測試條件:在輸入115/230Vac 和輸出相當小及比較大負載時,使用示波器帶寬為20MHz 連接到適配器的輸出端,同 時輸出端并聯一個47uF的電解電容和一個0.1uF的瓷片電容. At 115/230Vac input and output Min and Max.Load, the ripple and noise are as follows when measure with Max.Bandwidth of 20MHz and Parallel 47uF/0.1uF,crossed connected at testing point. 電壓比較大紋波/比較大噪音 Voltage Ripple and Noise(Max.) +5.9Vdc 120mV p-p 3.4 啟動延遲時間/Turn on delay time: 當輸入115Vac和輸出比較大負載時,比較大啟動時間為2S. 2Seconds M 福建12V1.5A韓規KCC認證電源適配器

廣東7.5V1.5A韓規KCC認證電源適配器

5.5-24Vdc 0.01A-4A ±2% ±5% 3.3 紋波和噪音Ripple and Noise: 測試條件:在輸入115/230Vac 和輸出相當小及比較大負載時,使用示波器帶寬為20MHz 連接到適配器的輸出端,同 時輸出端并聯一個47uF的電解電容和一個0.1uF的瓷片電容. At 115/230Vac input and output Min and Max.Load, the ripple and noise are as follows when measure with Max.Bandwidth of 20MHz and Parallel 47uF/0.1uF,crossed connected at testing point. 電壓比較大紋波/比較大噪音 Voltage Ripple and Noise(Max.) +5.9Vdc 120mV p-p 3.4 啟動延遲時間/Turn on delay time: 當輸入115Vac和輸出比較大負載時,比較大啟動時間為2S. 2Seconds M 3.5 上升時間/Rise time: 當輸入115Vac和輸出比較大負載時比較大時間為40 mS. 40 mS M 3.6 保持時間/Hold up time: 當輸入115Vac 和輸出比較大負載時,相當小保持時間為5 mS . 5 mS M 3.7 效率/Efficiency: 當115/230Vac輸入電壓時，1/4，1/2，3/4和滿載計算平均效率，相當小77.65%。 77.65%Min, At 115/230Vac input voltage,1/4，1/2，3/4 and full load ca廣東7.5V1.5A韓規KCC認證電源適配器

深圳市成康安科技有限公司是一家有著雄厚實力背景、信譽可靠、勵精圖治、展望未來、有夢想有目標，有組織有體系的公司，堅持于帶領員工在未來的道路上大放光明，攜手共畫藍圖，在廣東省深圳市等地區的家用電器行業中積累了大批忠誠的客戶粉絲源，也收獲了良好的用戶口碑，為公司的發展奠定的良好的行業基礎，也希望未來公司能成為*****，努力為行業領域的發展奉獻出自己的一份力量，我們相信精益求精的工作態度和不斷的完善創新理念以及自強不息，斗志昂揚的的企業精神將**深圳市成康安科技和您一起攜手步入輝煌，共創佳績，一直以來，公司貫徹執行科學管理、創新發展、誠實守信的方針，員工精誠努力，協同奮取，以品質、服務來贏得市場，我們一直在路上！